More Real Flower Resin Jewelry Tips, Tricks and Tutorials | Which Background Do You Prefer?


At any time due to the fact the dandelions began taking over earlier this yr, I have been harvesting, drying and embedding bouquets and leaves for building authentic flower jewelry.

Each time I do that, I experiment and attempt new points. Here are some of the things I have discovered. 

1st up are rubber finger cots.  I received a bag of black kinds right after I noticed a polymer clay instructor utilised them in her films. They definitely help preserve other fingers clean up in particular for running the smartphone digital camera. 

I to start with tried out guarding just my thumb and forefinger but it seems like one more lined would just take treatment of resin dye incidents. It’s seriously irritating to have dyed fingers for a working day or two otherwise. 

The types I obtained are built to just roll up each finger. But they ended up slim and everyone with long nails will shortly puncture them.  I received, at most, 2 uses out of each. Up coming time I will get the silicone versions which are supposed to be for protection when applying warm glue guns and need to final more time.  I briefly regarded recycling the good guidelines from normal washing up gloves but these had been also loose. 

The 2nd enhancement are the new measuring cups from Tiny Windows. Be aware : use BG1516 to get 15% discounted for anything at all there. I obtained some samples as Fran claims they are transitioning above to these much larger cups. 

With the previous cups, I normally evaluate 20 mL of Section A and 10 mL of Element B for a complete batch volume of 30 mL which are a lot easier markings for me to see and mark. The mixing although, experienced to be in a larger sized container.  

Smaller measurements are now attainable for 3 prevalent batch dimensions : 9 mL, 15 mL, 24 mL.  As you can see underneath, for 15 mL, the Aspect A and B markings are substantially clearer. All the mixing can performed in the same cup and thoroughly clean up for reuse is less difficult.  I considerably desire these as I frequently only have to have a little batch quantity. Lesser batches ensures all the resin will be applied up. 

Dry more than you want. I consider to select blooms which are not way too aged but at times it is difficult to notify. You can see the variation among these two dandelion bouquets just after drying. The leading one particular is plainly a bloom which is commencing to switch into the dandelion clock phase – it looks “furry” in the center. 

At the time I dip the bloom into the very first layer of resin, I gently “swish” it around, keeping the stalk with tweezers. This is to make guaranteed no air is trapped below. I do not suggest lifting the flower absolutely out of the resin. The petals clump jointly and I had a tough job making an attempt to open up up the petals all over again devoid of breaking just
about anything.

You can make obvious floral cabochons – I generally do it with 2 resin layers. But if you want to have a darkish track record, will not fill the molds to the brim but go away ample area to include a third colored resin layer. Greatest NOT to squirt alcoholic beverages inks immediately into that 3rd layer. Overflowing happened and I experienced hassle cleansing up so the cabochons turned out all right. 

….but much was obscured once I additional the bouquets and leaves!!  So possibly use a layer of colored resin or crystal clear resin with a resin film lower out. The bright yellow flower is the marsh marigold – I acquired a specimen from my regional yard heart for my garden. 

I am responsible of impatience and when I try and hurry, errors occur.  Bubbles are the biggest offenders.  The small kinds are in some cases inevitable but these at the edges can be retrieved some tape and incorporating additional new resin on best – but it is a lot more function.  I did not test usually adequate through the early curing stage and a late large bubble appeared in one particular of my oval cabochons. 

In potential, I will attempt to be far more individual and get the job done with a lot more resin layers. A bubble this sort of as this could be covered up efficiently by including an additional flower in the subsequent layer. Might be a interesting matter to attempt to make a 3D style. 

How thick an opaque track record layer can be will rely on whether a person would like to attach a glue on bail at the back or to drill a gap at the aspect for a screw eye pin. 

Obvious Backgrounds

Listed here is a swift refresher on how to make a uncomplicated genuine dandelion flower cabochon pendant – the video is on my beadinggem Instagram

I am not confident but I suspect quite a few people favor obvious backgrounds. Below are some illustrations :

The shrub rose at top rated remaining was the only 1 of 3 that I efficiently dried. The base left is a columbine flower which is pretty deep – I just reduce of
f the bottom of the flower. 

White Backgrounds

Colored Backgrounds 

These can assortment from the very light to dark as in black. 

The history in this set was basically tiny glass chips embedded in the very first resin layer:

The alcohol ink types from my recent try :

Remember to depart a comment underneath (scroll down) and enable us all know which shade you like. This will support everybody who is into real flower resin creating. 

Right before You Go:



This website might comprise affiliate links. I do acquire a smaller fee for any items bought through affiliate back links. This goes in direction of the support of this site and to supply useful resource data to viewers. The views expressed are only my individual. They would be the same whether or not or not I obtain any payment. 



Source hyperlink